Garmin nüvi 50LM Teardown: How to Open It and Replace the Screen, Battery, And Speaker

Garmin nüvi 50LM Teardown: How to Open It and Replace the Screen, Battery, And Speaker

JueMotyo JueMotyo Last updated on Nov 15, 2026

To open a Garmin nüvi 50LM, remove the four 9 mm screws on the back with a T4 Torx screwdriver, then pry the case open with a plastic tool. Inside, you can take out the motherboard, replace the battery (361-00056-00), replace the touchscreen, and replace the speaker. The battery and the speaker are both glued in place, so remove them slowly.

This teardown shows the full disassembly in order. Use it to fix a battery that won’t hold a charge, a cracked or unresponsive screen, or a speaker with no sound or poor sound.

Tools and Materials

  • T4 Torx screwdriver
  • Plastic pry tools (a blue plastic pry tool works well for the battery)
  • 530 adhesive remover (optional, for the glued speaker)
  • A flat, clean work surface

Use plastic tools, not metal. Metal can scratch the case and damage the circuit board.

Parts You May Need

Part Part Number / Name Fixes
Battery 361-00056-00 Fast drain, won’t charge, shuts off by itself
Touchscreen LCD Display Touch Screen Glass for Garmin nüvi 50LM Cracked glass, dead or wrong touch response, display faults
Speaker Garmin nüvi 50LM speaker No sound, low or distorted sound

Our parts are tested, original/OEM, 90–100% new, and come with a 3-month warranty.

Garmin nüvi 50LM GPS Navigator Disassembly: Step by Step

Step 1: Place the Device Face Down

Put the Garmin nüvi 50LM on a flat surface with the screen facing down. Turn it so the side with the speaker and charging port faces up.

Garmin nuvi 50LM placed face down on a flat surface

Step 2: Remove the Four Screws On Back Cover

Use the T4 Torx screwdriver to remove the four 9 mm screws on the back. Keep them in a small dish so none get lost.

Remove four 9 mm T4 Torx screws from Garmin nuvi 50LM back cover

Step 3: Pry the Back Cover Case Open

Slide a plastic pry tool into the seam and work around the edge until the Garmin nuvi 50LM back case opens.

Be careful: Do not pull the two halves apart quickly. There may be a ribbon cable between the screen and the motherboard. If you pull too hard, you can tear it. Lift slowly and check for cables first.

Insert plastic pry tool into Garmin nuvi 50LM case seam Pry around the edge of Garmin nuvi 50LM back case Garmin nuvi 50LM back case opened

Step 4: Remove the Motherboard

Remove the two 9 mm screws that hold the motherboard in place. Then lift the motherboard out of the device.

Garmin nuvi 50LM motherboard screws Remove the two 9 mm motherboard screws from Garmin nuvi 50LM Lift the motherboard out of Garmin nuvi 50LM

Step 5: Protect the Speaker Cables

A blue cable and a black cable connect the speaker to the motherboard. Handle them gently so you do not damage them.

Garmin nuvi 50LM speaker cables, blue and black

Step 6: Disconnect and Remove the Battery

  1. Unplug the red and yellow cables from the motherboard.
  2. Use the blue plastic pry tool to lift the battery slowly.
  3. The battery is stuck to the back cover with adhesive, so it may take firm pressure. Start at one edge and keep the tool flat.

Do not bend, puncture, or crush the battery.

Unplug red and yellow battery cables on Garmin nuvi 50LM Pry out Garmin nuvi 50LM battery 361-00056-00 with plastic tool

Step 7: Remove the Speaker

The speaker is glued in place, so do not pull it out by force. There are two ways to remove it:

  • Pry slowly: Lift one edge of the speaker with a plastic pry tool. Work along the edge a little at a time until the glue lets go.
  • Use 530 adhesive remover: Apply a small amount along the edge of the speaker and wait for the glue to soften. This removes the adhesive quickly and lets the speaker come off with less force.

Keep the remover away from the motherboard, the screen, and the cables. Use only a small amount. Clean off any extra glue before you fit the new speaker.

How to Put It Back Together

  1. Fit the new speaker and reconnect the blue and black cables.
  2. Place the new battery (361-00056-00) in the back cover.
  3. Plug the red and yellow cables into the motherboard.
  4. Reconnect the screen ribbon cable.
  5. Set the motherboard in place and secure it with the two 9 mm screws.
  6. Close the case and tighten the four 9 mm back screws.
  7. Charge the device, power it on, and test the touchscreen and the sound.

Which Part Should You Replace?

Problem Replace
Battery drains fast or won’t charge Battery 361-00056-00
Cracked glass, or touch is slow or wrong Touchscreen
No sound or crackling sound Speaker

Safety Tips

  • Turn off the device and unplug it before you open it.
  • Never use a sharp metal tool on the battery.
  • If the battery looks swollen, handle it carefully and recycle it properly.
  • Keep 530 adhesive remover away from the screen and the circuit board.

Frequently Asked Questions

What screwdriver do I need to open a Garmin nüvi 50LM?
A T4 Torx screwdriver. The back has four 9 mm screws.

How do I remove the glued speaker in a nüvi 50LM?
Lift the edge slowly with a plastic pry tool, or apply a small amount of 530 adhesive remover to soften the glue first.

What battery does the nüvi 50LM use?
The part number is 361-00056-00.

Which cables do I unplug to remove the battery?
The red and yellow cables on the motherboard.

Why is the battery hard to remove?
It is glued to the back cover. Use steady pressure with a plastic pry tool and keep it flat.

Can I replace the nüvi 50LM screen myself?
Yes. Open the device with the steps above, remove the motherboard, and swap the touchscreen. Be careful with the ribbon cable.

Where can I buy nüvi 50LM replacement parts?
At huayuxt.com. We have 9 years of experience selling Garmin parts, and every part is tested and covered by a 3-month warranty.

Вернуться к блогу