Garmin Montana Power Button Broken? Here's the Easy Fix
Replacement of this button is an easy procedure that takes around 10 minutes. This guide covers the Montana 600, 600t, 610, 610t, 650, 650t, 680, and 680t models; do not assume it applies to every Montana model.

Browse our Garmin Montana repair parts collection after identifying the damaged component. If the rubber cover appears intact but the device will not power on, start with the Garmin troubleshooting center before ordering a button: replacing the outer rubber does not establish or fix the cause of an internal electrical fault.
Quick Tip
The rear housing design is shared across multiple Montana models.
- Montana 600 / 600t / 610 / 610t replacement back cover options: choose Back cover case (no port protection covers) for the housing, or Protection covers for the separately listed covers. The housing is listed without a battery.
- Montana 650 / 650t / 680 / 680t replacement back cover options: Battery Cover and Back Cover Case styles 1, 2, and 3 are separate choices. Match the required component and style to your device; do not assume a battery or all covers are included.
Check the exact model, camera opening, and housing style before ordering. A battery cover, full rear housing, and replacement outer button are different components and should not be chosen interchangeably.
Tools You'll Need to Replace the Garmin Montana Power Button
Before starting the repair, prepare the following tools:
- A sharp hobby knife or precision utility knife
- Super glue (502 glue or Loctite 406 is recommended)
- Replacement power buttons for Montana 600 / 600t / 610 / 610t / 650 / 650t / 680 / 680t, 5-piece pack
- Isopropyl alcohol and a cleaning cloth or cotton swab
The linked button listing is a 5-piece pack, not a single button or complete rear housing. Check the part against the damaged outer button before cutting.
One advantage of this repair is that you do not need to completely disassemble the Garmin GPS. The replacement can be completed directly from the outside, saving time and reducing the risk of damaging internal components.
Garmin Montana 600 & 650 Power Button Replacement Guide
Step 1 – Mark the Cutting Area

Although removing the rear housing is possible, it is not recommended for this repair because it adds unnecessary work and increases the chance of damaging the waterproof seal.
Instead, compare the replacement power button with the original damaged rubber button.
Use the replacement part as a reference and carefully identify the portion of the old rubber that needs to be removed. Mark the cutting area before beginning.
Accurate cutting marks will make installation much cleaner and easier.
Step 2 – Carefully Remove the Damaged Rubber


Using a sharp hobby knife, carefully cut along the reference lines.
Remove only the damaged rubber portion while keeping the surrounding housing intact.
Take extra care around the edges because this is the area most likely to slip. Cutting slowly will produce a much cleaner result and help the new button fit perfectly.
Step 3 – Apply Adhesive and Install the New Button

Once the damaged rubber has been removed, clean away any debris.
Apply a thin layer of 502 super glue or Loctite 406 around the edge of the cut opening.
Immediately position the replacement power button over the opening and press it firmly into place.
Avoid using excessive glue, as a small amount provides sufficient bonding strength while reducing cleanup later.
Allow the adhesive to cure according to the manufacturer's recommended drying time before operating the button.
Step 4 – Clean Away Excess Glue

After the new button has been installed, inspect the surrounding area.
Use isopropyl alcohol and a soft cloth or cotton swab to wipe away any excess adhesive before it fully hardens.
Cleaning the area improves both appearance and button movement.
Once everything is dry, test the button several times to confirm smooth operation.
Important Tips When Replacing the Garmin Montana Power Button
Keep the following precautions in mind:
- Always cut away from your fingers when using a hobby knife.
- Remove only the damaged rubber—avoid cutting the surrounding housing.
- Use a high-quality adhesive such as 502 or Loctite 406 for the strongest bond.
- Apply only a thin layer of glue to prevent overflow.
- Purchase a precisely molded replacement button designed specifically for the Montana series.
- Allow the adhesive to fully cure before pressing the button repeatedly.
Taking a few extra minutes during installation will greatly improve the durability of the repair.
Conclusion
Replacements of the damaged power button on the Garmin Montana series including 600, 600t, 610, 610t, 650, 650t, 680, and 680t models is an easy fix that anyone can do.
In just four easy steps and within 10 minutes, you'll be able to get your GPS back into working order without having to replace the entire housing of your device.
At Huayuxt, we specialize in original-quality Garmin replacement parts, including power buttons, LCD screens, touch screens, back cover cases, battery covers, front housings, and other repair components for the Garmin Montana series.
Whether your Montana has a broken power button, cracked screen, worn housing, or damaged back cover, we're committed to helping you extend the life of your trusted GPS device—so it can continue guiding your adventures for years to come.
Need Help With Your Montana Repair?
If you are unsure whether the outer rubber button or an internal switch has failed, or need help selecting the correct housing variant, review our Garmin repair services before cutting the old button or ordering parts.